Skip to main content
Contec GmbH – Home
  • Applications
    • Analysis & vacuum technology
    • Construction & agricultural machinery
    • Chemistry
    • Gas and steam turbines
    • Laboratory equipment
    • Food & beverage industry
    • Air technology & air pollution control
    • Measurement technology
    • Motorsport / Racing
    • Commercial vehicles & trailers
    • Paper & pulp industry
    • Process water
    • Lubricating oil systems
    • Seawater & Desalination Plants
    • Steel industry
    • Power generators
    • Tanks
    • Compactors & compressors
    • Water treatment & supply
    • Wine and juices
  • Air and gas filters
    • Filter housings
      • Aluminum filter housings
      • Aluminum and polyamide filter housings
      • DIF | Disposable In-Line Filters
      • PTFE filter housings
      • Polyamide filter housings
      • Stainless steel filter housings
    • Filter elements
      • PTFE filter elements
      • Composite microfiber elements
      • Stainless steel filter elements
    • Adsorber housings and adsorbents
      • Adsorbents
      • DIA | Disposable In-Line adsorbers
      • Adsorber vessels, IAH series
  • Oil mist filtration
    • Standard and special designs
    • With compressed-air drive/vacuum generator
  • Liquid filters
    • Filter housings
      • Plastic filter housings
        • SF Cartridge filter housings
        • Single-place filter housings
        • Bag filter housings
      • Stainless steel filter housings
        • Membrane filter housings
        • Cardrige filter housings
        • Bag filter housings
        • Multi-bag filter housings
    • Filter elements
      • Filter cartridges
      • Filter bags
      • Sieve elements
      • Membrane filters
      • Split tube elements
    • Wedge wire filters
      • Wedge wire filters
      • Control systems
      • Split-tube elements
    • Fully automatic filters
      • Backwashing filter FMA
  • Level measurement
    • Liquid level sensors
    • Liquid level switches
    • Liquid level indicators
    • Temperature switches
  • Service/Retrofit
  • Company
    • Azubis gesucht!
    • News
  • Contact
Menu
DEEnglish

FAQs

COGA is the registered term used by Contec’s Air and Gas Filtration division and stands for Contec Gas and Air Filters (COGA).

In addition to the type (or, more accurately, the physical state) of the medium to be filtered (liquid or gas), the following specifications are important for designing a filter system: the flow rate (e.g., in m³/h), the operating pressure (e.g., in bar), the operating temperature (in °C), the viscosity or density of the medium, the solids content or the quantity of particles or aerosols to be separated, and the required filter fineness or separation efficiency.

In process engineering, separation efficiency describes the effectiveness of a separation process. It defines the ratio of the material retained by the filter (e.g., dust particles or aerosols) compared to the unpurified medium fed into the system.

The burst pressure indicates the failure of the filter element when fluid flows from the inside out. At the burst pressure, the filter element is destroyed, and the unfiltered medium flows through the filter. The burst pressure is many times higher than the permissible nominal pressure or operating pressure.

Nominal pressure describes the pressure in bar/mbar/kPa for which the filter is designed at room temperature (20°C).

Service life - that is, the determined operating duration of the filter - depends on the degree of contamination in the medium to be filtered, the required separation efficiency, the filter size, and the flow rate.

Viscosity indicates how viscous a medium is. As a general rule, the higher the viscosity of the medium, the more complex the requirements for the filter system become.

In particle filters, particles are separated from gases or liquids by directing the fluid flow into a housing with two connections and through a particle filter element. The flow direction within the filter element is from the outside to the inside.

In coalescence filtration, the flow direction within the filter element is from the inside to the outside. The coalescence filter element essentially consists of two parts: an inner coalescence layer and a coarser outer layer for draining the liquid. The aerosols or droplets are captured by the fine fibers of the inner layer, accumulate as they pass through the outer layer of the filter element, and enter the collection container from there. 

Viton®, Nylon®, Neoprene®, etc., are registered trademarks. For example, the Viton® brand from Chemours/DuPont refers to a fluoroelastomer (FKM/FPM). Kalrez® is also from DuPont and refers to a synthetic rubber (polychloroprene, CR). Neoprene® is an extremely flexible, elastic, and waterproof material with high resistance to chemicals, weathering, and oils. Nylon® is the brand name for a polyamide (PA). Chemraz® is the brand name for a perfluoroelastomer (FFKM) manufactured by Greene Tweed.

A filter housing essentially consists of the upper part (head) and the lower part (sump/cup), which together enclose the filter element. There is a gasket between the head and the sump, the material of which varies depending on the filter medium. The filter housing is equipped with connections (inlet/outlet), brackets, etc. The filter housing is made, for example, of aluminum, stainless steel, plastic, or combinations thereof.

Filter housings offer a wide range of connection options, primarily as female threads in inch sizes ranging from 1/8 to 3". Typical connection types include inch threads (BSPP, BSPT, NPT).

A differential pressure indicator is used to find how “clogged” a filter element is. This allows you to determine when the filter element should be replaced to ensure the system functions properly and to prevent costly downtime.

Filtration, absorption, and adsorption are separation processes: 
Filtration mechanically separates solids using screens or filters. Adsorption binds substances (gas/liquid) to the surface of a solid. Absorption, on the other hand, absorbs substances into the interior of a material (by volume).

  • Filtration (mechanical): A mixture of solids and liquids or gases is passed through the filter medium. The solids are retained based on their size.
  • Adsorption: Adsorption refers to the attachment of atoms or molecules from liquids or gases (adsorbate) to a solid surface (adsorbent). It is often used for purifying gases.
  • Absorption: Absorption refers to the uptake or incorporation of substances into another material or body. The gases or liquids to be filtered (absorbate) penetrate the interior of another substance (absorbent). This involves physical or chemical dissolution.

Drain valves on filter housings are used for controlled emptying, pressure relief, or condensate drainage. This allows the housing to be emptied, for example, before a filter change, or for contaminants to be drained without having to interrupt the filtration process.

Depending on the application, drain valves range from simple manual valves to automatic systems. Common types include manual drain valves, automatic float-type drain valves, electronic solenoid valves, and pressure relief valves.

Filter size depends on many factors, such as the separation efficiency, the desired filtration result, the expected service life, and the purchase cost. Contec will be happy to provide you with quick and expert advice, taking all necessary parameters into account.

A filter housing essentially consists of the upper housing (head) and the lower housing (sump/cup), which together enclose the filter element. Between the head and the sump is a gasket, the material of which varies depending on the filter medium. The filter housing is equipped with connections (inlet/outlet), brackets, etc.

Filter housings offer a wide range of connection options, primarily as female threads in inch sizes ranging from 1/8 to 3". Typical connection types include inch threads (BSPP, BSPT, NPT).

Aluminum filter housings are significantly lighter and have better thermal conductivity than stainless steel filter housings. They are also more cost-effective to purchase.

Depending on the model, Contec PTFE and PE filter cartridges, stainless steel elements, disposable microfiber composite elements, and adsorbents can be used.

Filter housings essentially consist of a head and a sump. In Contec aluminum filter housings, the head and sump may be made of different materials. To clearly indicate the materials used at a glance, the first letter refers to the head material, and the second letter refers to the sump material. Thus, AA stands for an aluminum-aluminum combination, and AN for an aluminum-polyamide combination.

Due to the corrosion resistance of aluminum filter housings and their pressure resistance, they are ideally suited for use as particle and coalescing filters (oil separation) in the food, chemical, and pharmaceutical industries.

A differential pressure indicator is used to find how “clogged” a filter element is. This allows you to determine when the filter element should be replaced to ensure the proper functioning of the system and to prevent costly downtime.

Drain valves on filter housings are used for controlled drainage, pressure relief, or condensate drainage. This allows the housing to be drained, for example, before a filter change, or for contaminants to be drained without having to interrupt the filtration process.

Depending on the application, drain valves range from simple manual valves to automatic systems. Common types include manual drain valves, automatic float-type drain valves, electronic solenoid valves, and pressure relief valves.

JDepending on the model, Contec PTFE and PE filter cartridges, stainless steel elements, disposable microfiber composite elements, and adsorbents can be used.

Contec aluminum/polyamide filter housings are suitable for filtration in compressed air systems, gases, and hydraulic return lines, particularly in plant engineering, process engineering, and laser technology. Thanks to the combination of robust, anodized aluminum and chemical-resistant polyamide, they are suitable for applications up to 10 bar. While the filter housing head provides stability, pressure resistance, and corrosion resistance through anodization, the polyamide filter housing base is resistant to oils, greases, and hydrocarbons.

The transparent polyamide sump of the filter housing is resistant to many solvents, oils, and aggressive media, allows for visual inspection of the medium and filter element, and is easy to clean.

The abbreviation DIF stands for “Disposable In-Line Filter”. Disposable in-line filters (DIF) are small, compact disposable filters that are integrated directly into pipelines or hoses for the purification of gases, compressed air, or liquids.

The housing of a DIF is made of transparent Nylon® or polyvinylidene fluoride, and the “sealed-in” filter element is made of microfiberglass. 

Contec DIF are frequently used to protect analytical instruments, pumps, or pneumatic systems.

Disposable in-line filters (DIF) are integrated directly into pipelines or hoses. They filter by separating solids, particles, and contaminants from the medium (air or gas) based on their size. This occurs primarily through surface filtration (“sieve effect”) or depth filtration (entrapment within the pores).

PTFE is the abbreviation for “polytetrafluoroethylene”. PTFE is a linear polymer composed of fluorine and hydrocarbons. This semi-crystalline fluoroplastic has an extremely strong bond between the carbon and fluorine atoms. Colloquially, this plastic is often referred to by the trade name Teflon, owned by DuPont. PTFE is highly heat-resistant.

Its outstanding thermal and chemical resistance make PTFE one of the most versatile plastics in air, gas, and liquid filtration. In the Contec filter range, PTFE is used in membrane filters, cartridge filters, and the filter housings themselves.

PTFE filter housings offer extremely high chemical resistance to acids, bases, and solvents. They are characterized by high temperature resistance (up to 150°C), hydrophobic properties, durability due to low friction and abrasion resistance, and ease of cleaning. PTFE filter housings are ideal for sterile and gas filtration.

PTFE is the material abbreviation for “polytetrafluoroethylene”. Colloquially, this plastic is often referred to by the trade name Teflon® from DuPont. PTFE is a linear polymer composed of fluorine and hydrocarbons. This semi-crystalline fluoroplastic features an extremely strong bond between the carbon and fluorine atoms. PTFE is highly temperature-resistant.

Due to their extremely high chemical resistance, temperature resistance (up to 150°C), and hydrophobicity (water-repellent properties), Contec PTFE filter housings are primarily used in the chemical industry, pharmaceutical production, semiconductor manufacturing, and gas and air filtration. Contec PTFE filter housings are ideal for aggressive solvents, acids, alkalis, and sterile applications.

Drain valves on filter housings are used for controlled emptying, pressure relief, or condensate drainage. This allows the housing to be emptied, for example, before a filter change, or for contaminants to be drained without having to interrupt the filtration process.

Depending on the application, drain valves range from simple manual valves to automatic systems. Common types include manual drain valves, automatic float-type drain valves, electronic solenoid valves, and pressure relief valves.

The PTFE filter housing essentially consists of the upper housing (head) and the lower housing (sump/cup), which together enclose the filter element. Between the head and the sump is a gasket, the material of which varies depending on the filter medium. The filter housing is supplemented with connections (inlet/outlet), brackets, etc.

PTFE filter housings offer a wide range of connection options, primarily as female threads in inch sizes ranging from 1/8 to 3". Typical connection types include inch threads (BSPP, BSPT, NPT).

Polyamide (PA) filter housings are most commonly used in the industrial filtration of air, gases, and liquids due to their high chemical resistance. Primary applications include chemical, paint, and coating production, solvent purification, water treatment, wastewater treatment plants, and the electronics and photography industries.

Polyamide - or, colloquially, Nylon® - filter housings from Contec are cost-effective yet high-quality filter housings. Their sump can be made transparent, allowing the filter element and, if applicable, the separated contaminants to be visible. Ideal for use in compressed air systems.

Polyamide (PA), often known by the brand name Nylon®, is a versatile synthetic thermoplastic. It is characterized by high strength, elasticity, abrasion resistance, and dimensional stability. Due to its robustness, it is well-suited for use as a filter housing.

A filter housing essentially consists of the upper housing (head) and the lower housing (sump/cup), which together enclose the filter element. Between the head and the sump is a gasket, the material of which varies depending on the filter medium. The filter housing is supplemented with connections (inlet/outlet), brackets, etc.

Filter housings offer a wide range of connection options, primarily as female threads in inch sizes ranging from 1/8 to 3". Typical connection types include inch threads (BSPP, BSPT, NPT).

Stainless steel filter housings from Contec are robust, corrosion-free, and temperature-resistant (over 200°C), and can withstand high operating pressures. Stainless steel filter housings are easy to clean and can be customized to fit the specific system. 

  • Laboratory technology
  • Analytics
  • Instrumentation
  • Pressure ranges up to 1,400 bar
  • Vacuum

All COGA standard stainless steel filter housings are manufactured entirely from 316L stainless steel and are weld-free in accordance with NACE MR-01-75. Each filter housing has a serial number to ensure traceability. Material certificates in accordance with EN 10204-3.1 can be provided for the filter housings.

All COGA filter housings comply with the requirements of the Pressure Equipment Directive 2014/68/EU. The filter housings that are required to be marked accordingly bear the CE mark, as mandated by law.

A stainless steel filter housing essentially consists of the upper housing (head) and the lower housing (sump/cup), which together enclose the filter element. Between the head and the sump is a gasket, the material of which varies depending on the filter medium. The filter housing is equipped with connections (inlet/outlet), mounting brackets, etc.

Stainless steel filter housings offer a wide range of connection options, primarily as female threads in inch sizes ranging from 1/8 to 3". Typical connection types include inch threads (BSPP, BSPT, NPT).

Drain valves on filter housings are used for controlled draining, pressure relief, or condensate drainage. This allows the housing to be drained, for example, before a filter change, or to remove contaminants without having to interrupt the filtration process.

Depending on the application, drain valves range from simple manual valves to automatic systems. Common types include manual drain valves, automatic float-type drain valves, electronic solenoid valves, and pressure relief valves.

A differential pressure indicator is used to find how “clogged” a filter element is. This allows you to determine when the filter element should be replaced to ensure the system functions properly and to prevent costly downtime.

Disposable filter elements offer excellent filtration properties specifically tailored to the medium, with low pressure drops and a long service life. They are generally a very economical, cost-effective solution. No cleaning is required; filter elements are replaced on a one-for-one basis. When changing media, the filter can be easily and individually adapted to the new medium.

PTFE stands for “polytetrafluoroethylene”. PTFE is a linear polymer composed of fluorine and hydrocarbons. This semi-crystalline fluoroplastic features an extremely strong bond between the carbon and fluorine atoms. Colloquially, this plastic is often referred to by the trade name Teflon, owned by DuPont. PTFE is highly temperature-resistant.

Its outstanding thermal and chemical resistance make PTFE one of the most versatile plastics in air, gas, and liquid filtration. In the Contec filter range, PTFE is used in membrane filters, cartridge filters, and - since PTFE is inert and cannot adsorb - in the filter housings themselves.

PTFE filter elements are manufactured by sintering pure PTFE granules. No additives are used. These filter elements are ideal whenever only 100% pure PTFE can be used. Generally, if suitable, a disposable K-type filter element is preferable, as it outperforms PTFE filters in terms of both pressure drop and service life.

The advantages of PTFE include higher temperature resistance up to 200°C and better chemical resistance to certain substances. PTFE filter elements are available in 2 µm and 20 µm pore sizes and can be cleaned using ultrasound.

Stainless steel filter elements are ideal for applications with high contaminant loads and as pre-filters for disposable final filter types.

Stainless steel filter elements are wear-resistant and reusable. Depending on their mesh size, they can be cleaned and reused repeatedly.

Glass fiber filter elements offer outstanding filtration properties with very low pressure drops and, with a holding capacity of approximately 90%, have a very long service life.

In particle filtration, particles are separated from gases or liquids by directing the fluid flow into a housing with two connections and through a particle filter element. The flow direction within the filter element is from the outside to the inside.

In coalescence filtration, the flow direction within the filter element is from the inside to the outside. The coalescence filter element essentially consists of two parts: an inner coalescence layer and a coarser outer layer for draining the liquid. The aerosols or droplets are captured by the fine fibers of the inner layer, accumulate as they pass through the outer layer of the filter element, and enter the collection container from there. 

There are two different types of filter elements. Particle filter elements use a single layer of filter media, whereas coalescence filter elements feature a fine capture layer on the inside and a coarse drainage layer on the outside. Depending on the application, various binders such as epoxy resin, PVDF silicate, or silicone are available.

The binders vary depending on the application:

E - Epoxy resin binders are suitable for all applications involving particle removal in non-corrosive gases and liquids.
K - PVDF binders offer excellent chemical resistance in corrosive gases and liquids. Very low adsorption.
S - Silicate binders produce a completely inorganic filter element. Very well suited for high temperatures and solvent applications.
L - Silicone binders have a hydrophobic effect and prevent pores from becoming clogged with condensate. The maximum temperature is 200°C.

Contec adsorbers are used for fine gas purification when mechanical separation methods are no longer sufficient. An adsorber is a system consisting of an adsorber housing and internal adsorbents. The adsorbents used depend on the substances to be filtered, e.g., CO2 or various halogens.

Adsorbents are used for:

  • Drying gases
  • Catalytic gas purification
  • Removing carbon dioxide (CO2)
  • Removal of carbon monoxide (CO)
  • Removal of sulfur-containing gases (SO2, SO3, H2S, CS2, COS)
  • Removal of nitrogen oxides (NOx, NO, NO2)
  • Removal of ammonia (NH3)
  • Removal of halogens (Cl₂, Br₂, I₂, HCl, HBr, HI, etc.)
  • Removal of heavy metal compounds (Hg, As compounds, etc.)
  • Removal of metallic mercury (HgO, amalgam)
  • Removal of odorous substances, oil vapors, gasoline, and tar condensates
  • Removal of toxic and carcinogenic compounds (furans, dioxins, aromatic compounds, phenol, etc.)
  • Removal of radioactive substances (Cs, U, Pu compounds, etc.)

Disposable in-line adsorbers (DIA) offer excellent filtration properties specifically tailored to the medium, with low pressure drops and a long service life. This is generally a very economical and cost-effective solution. Cleaning is not required; filter elements are replaced on a one-for-one basis. When changing media, the filter can be easily and individually adapted to the new medium.

Disposable in-line adsorbers (DIA) are used for fine gas purification when mechanical separation methods are no longer sufficient. Disposable in-line adsorbers (DIA) consist of a PA or PVDF housing filled with adsorbent granules, featuring integrated filter fleece at the inlet and outlet. The adsorbents used depend on the substances to be filtered, e.g., CO2 or various halogens.

IAH adsorber vessels are used for: 

  • Fine gas purification
  • Gas drying
  • Removing specific gaseous impurities from air and non-corrosive gases
  • Zero-gas generation

IAH adsorber containers are available with filling volumes ranging from 23 to 1018 ml.

Adsorber containers in the IAH series are made of Plexiglas® with lids made of PVC-U or anodized aluminum (IAH300A series) and can be filled with a wide variety of sorbents.

The advantages of adsorber containers are numerous. They:

  • can be filled by the user
  • can be refilled as often as needed
  • are easy to open
  • are transparent, allowing for visual inspection of the sorbent level
  • provide filter pads at the gas inlet and outlet to support the sorbent
  • ensure uniform flow and act as
  • dust filters

Contact

Contec GmbH Industrieausrüstungen
Heideweg 24
53604 Bad Honnef
Germany

P. +49 (0)2224 9893-0
F. +49 (0)2224 9893-20

Contec on LinkedIn (opens in a new window)

Products

  • Air and gas filters
  • Oil Mist Filtration
  • Liquid filters
  • Level measurement

Accessories

  • Suction filters
  • Seals
  • Filter elements
  • Manometer
  • Side channel blowers

About Contec

  • Company
  • Certifications
  • News
  • Contact
  • FAQ

Legal

  • Imprint
  • Data protection declaration

(c) Contec GmbH Industrieausrüstungen

Contec GmbH - Official Practice Partner for the Dual Study Program at IU (International University)
  • Cookie-Settings
  • Applications
    • Analysis & vacuum technology
    • Construction & agricultural machinery
    • Chemistry
    • Gas and steam turbines
    • Laboratory equipment
    • Food & beverage industry
    • Air technology & air pollution control
    • Measurement technology
    • Motorsport / Racing
    • Commercial vehicles & trailers
    • Paper & pulp industry
    • Process water
    • Lubricating oil systems
    • Seawater & Desalination Plants
    • Steel industry
    • Power generators
    • Tanks
    • Compactors & compressors
    • Water treatment & supply
    • Wine and juices
  • Air and gas filters
    • Filter housings
      • Aluminum filter housings
      • Aluminum and polyamide filter housings
      • DIF | Disposable In-Line Filters
      • PTFE filter housings
      • Polyamide filter housings
      • Stainless steel filter housings
    • Filter elements
      • PTFE filter elements
      • Composite microfiber elements
      • Stainless steel filter elements
    • Adsorber housings and adsorbents
      • Adsorbents
      • DIA | Disposable In-Line adsorbers
      • Adsorber vessels, IAH series
  • Oil mist filtration
    • Standard and special designs
    • With compressed-air drive/vacuum generator
  • Liquid filters
    • Filter housings
      • Plastic filter housings
        • SF Cartridge filter housings
        • Single-place filter housings
        • Bag filter housings
      • Stainless steel filter housings
        • Membrane filter housings
        • Cardrige filter housings
        • Bag filter housings
        • Multi-bag filter housings
    • Filter elements
      • Filter cartridges
      • Filter bags
      • Sieve elements
      • Membrane filters
      • Split tube elements
    • Wedge wire filters
      • Wedge wire filters
      • Control systems
      • Split-tube elements
    • Fully automatic filters
      • Backwashing filter FMA
  • Level measurement
    • Liquid level sensors
    • Liquid level switches
    • Liquid level indicators
    • Temperature switches
  • Service/Retrofit
  • Company
    • Azubis gesucht!
    • News
  • Contact